STEP 01
Mount the front camera.
Clean and dry the windshield. Apply the electrostatic sticker, then secure the adhesive mount behind the rear-view mirror without obstructing your view.
← All product supportTwo views.
Product support / F30
Two views.
One clear guide.
Set up your F30, connect Rexing Connect, and find the footage you need—from the road ahead to the view behind.
Download F30 manual ↗01 / Start with the essentials
Connect both cameras.
Complete setup while parked. Keep the camera and cables clear of your view, airbags and moving parts.
STEP 02
Connect the rear camera.
Mount the rear camera and connect its included cable to the front unit’s rear-camera port. Check the rear view before finishing the cable routing.
STEP 03
Power up and check.
Insert a compatible card with power off. Connect the supplied car charger to the USB-C power port and the vehicle’s 12V accessory socket.
Ready to record: F30 starts recording automatically when powered. A flashing red indicator confirms recording is in progress.
02 / Prepare your storage
A fresh card.
A reliable start.
The F30 installation guide specifies Class 10 / UHS-I or higher microSD cards, up to 128GB.
Back up before formatting.
Formatting deletes recordings, including locked files. Save important footage before inserting a card that may need formatting.
1. Insert with power off.
Push the card into its slot until it clicks. Never insert or remove a card while the camera is powered.
2. Allow initial formatting.
Power on with the card inserted. The manual says that if formatting is required, a prompt appears and formatting starts automatically. It may take a few minutes.
3. Confirm recording.
After formatting finishes, recording starts automatically. Check the flashing red indicator and verify a short saved clip in the app.
03 / Pair with Rexing Connect
Your phone.
Your camera controls.
- Power the F30.Wi-Fi enters standby automatically. Press the camera button to display the Wi-Fi page if needed.
- Join the displayed network.In your phone’s Wi-Fi settings, select the network name shown by your camera. The default password in the manual is 12345678.
- Open Rexing Connect.Tap Connect to access live view, settings and recordings. If prompted, keep the camera’s Wi-Fi connection even without internet access.
04 / Review and save
Your recordings, within reach.
Use the app for playback and downloads. Use a compatible GPS video player to review recorded route and speed information.
Watch and download.
- Open Video in Rexing Connect.Connect to the camera first, then open playback from the app home screen.
- Choose your recording.Check unlocked and locked video categories for the clip you need.
- Save a copy.Hold a clip to select it, then tap Download. Confirm the copy is saved before formatting the card.
Review your drive with GPS.
The F30’s GPS mount records vehicle location and speed. It searches for a signal when the camera receives power; the GPS icon changes once a signal is active.
For computer playback, power off before removing the card, then copy the files with a compatible card reader.
Find GPS video player downloads →Protect an important moment: Hold the camera button for 3 seconds to lock the current clip. Locked files are stored under CARDV / MOVIE / RO and are not overwritten by loop recording.
05 / Choose the correct parking setup
Different kits.
Different settings.
Parking monitoring requires compatible hardwire power. Kits are sold separately; confirm F30 connector compatibility before purchase or installation.
Smart or OBD Smart Hardwire Kit
The F30 manual describes impact-triggered parking recording with a compatible Smart or OBD Smart Hardwire Kit. The camera switches between parking and normal recording as vehicle power status changes.
App Parking Monitor: enable with the required kitDo not enable Parking Monitor without the compatible smart hardwire kit connected.
360° Intelligent Hardwire Kit
The kit’s motion sensor powers the camera when it detects movement. The kit controls when motion-triggered recording starts.
App Parking Mode: OFFThe F30 manual requires Parking Mode to remain off in Rexing Connect when using this motion-sensing kit.
Parking recording can stop when battery voltage is low.
A hardwire kit’s low-voltage protection may cut power to protect the vehicle battery. Frequent recording can use available battery power; after cutoff, motion cannot start recording until the kit supplies power again. Cutoff and restart behavior depend on the installed kit.
06 / Troubleshooting
Get back to
recording.
Start with camera power, the memory card and your phone’s Wi-Fi connection.
Ask Rexing support →Which memory card should I use?
Use a Class 10 / UHS-I or higher microSD card, up to 128GB, following the F30 installation instructions. Power off before inserting or removing it. For a larger card, ask Support to confirm compatibility with your unit first.
Why can’t my phone connect to the camera?
Keep the camera powered, open the phone’s Wi-Fi settings and join the network shown on the camera. Then open Rexing Connect and tap Connect. If your phone warns that this Wi-Fi has no internet, keep the Wi-Fi connection for camera access.
What do the screen indicators mean?
Gray indicates Wi-Fi standby; green indicates the app is connected. Flashing red means recording is in progress; flashing yellow means the current video is locked.
How do I lock a recording?
Hold the camera button for about 3 seconds to lock the current clip. Locked files are protected from loop overwriting and can be found in the RO folder under CARDV / MOVIE on the card. Formatting still erases them.
Why is the memory card full?
Loop recording overwrites the oldest unlocked videos. Locked clips remain on the card, so back up important recordings and format the card when needed. The manual’s default G-sensor setting is Low.
How do I correct the time and date?
Connect the F30 to your phone through Rexing Connect. The current manual says the camera time and date sync automatically with the phone when the app connects.
Why does parking recording stop?
Check power from the installed hardwire kit and verify the setting for that kit. Low-voltage protection can cut camera power to protect the vehicle battery; when power is cut, parking recording cannot operate. Refer to your kit’s instructions for its cutoff and restart behavior.
Which firmware should I install?
Contact Support with the F30 model label, current firmware version and the issue you want to resolve. Do not use firmware for a similarly named model or assume that an update alone enables parking monitoring without its required hardware.
07 / Downloads and help
Made for your F30.
F30 user manual ↗Setup & operation · March 2026 revision · PDFApps & GPS player →Phone connection and desktop playbackFirmware assistance →Confirm the right update for your camera
Need a hand?
Share your model, firmware version and the issue with our team.
Register your camera ↗ · Warranty & returns →Based on the F30 User Manual REV03202026. Available settings may vary with firmware.